M 3 1 8 0 E    MINISCRIBE

CLick For Homepage 4drives.com
Your #1 Source For Out Of Production, Obsolete, And Hard To Find Hard Drives
CLICK ON THE LOGO ABOVE TO CHECK PRICE AND AVAIABILITY OF THIS DRIVE.

This information is provided as-is for free and Discount Computer Peripherals, Inc. shall not be held liable for any errors or omissions

.

                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 5.25"/HH              Cylinders    1250|     |     |
Capacity form/unform   156/  182 MB        Heads           7|     |     |
Seek time   / track  17.0/ 4.0 ms          Sector/track   35|     |     |
Controller           ESDI                  Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate    1.250 MB/S int       Bytes/Sector      512
                            MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C        10 50    |    -40 60
Power: sleep              W     Humidity     %         8 80    |      8 80
       standby            W     Altitude    km    -0.061  3.048|        12.192
       idle          15.0 W     Shock        g        10       |     40
       seek          18.5 W     Rotation   RPM      3600
       read/write         W     Acoustic   dBA        46
       spin-up            W     ECC        Bit
                                MTBF         h      35000
                                Warranty Month
Lift/Lock/Park     YES          Certificates     CSA,FCC,IEC380,UL478,VDE     

**********************************************************************
                        L   A   Y   O   U   T
**********************************************************************
MINISC.  3180E  PRODUCT MANUAL 1102 P2, 06/08/88

  +-----------------------------------+----------+----------+
  |                                   +----------J8         |XX
  |                                 J21xx                   |XX J2
  | +J6                          J23*** xxJ14               |XX
  | +-+                              J510X                  |XX1
  |1--J15                              J24xx xxJ20          |
  |+--+                                     J11 J12         |
  |                                    J10xx xx xx xxJ13    |XX
  |                                 J19xx     J27xx xxJ30   |XX
  |                                 J29xx                   |XX
  |+-+                                                      |XX J1
  || |                                                      |XX
  |+-J7                                    xxJ9             |XX
  |                                                         |XX1
  |                                                   xxJ4  +-+
  |                                                           |
  |                                                          XXJ3
  |                                          +---J5          XX Power
  +------------------------------------------+---+------------+



**********************************************************************
                      J   U   M   P   E   R   S
**********************************************************************
MINISC.  3180E  PRODUCT MANUAL 1102 P2, 06/08/88

 Jumper Setting
 ==============

 J4 Spindle Control Option
 -------------------------
 J4 CLOSED The 3180E must wait for a start spindle command to start
           the spindle motor.
    OPEN   The drive automatically starts the spindle motor at power
           on.


 J19/13/14 Sector Configuration Options
 --------------------------------------
 J19/J13/J14 CLOSED The drive is configured to operate in soft
                    sectored mode. ADDRESS MARK GENERATION and
                    DETECTION are enabled, and the SECTOR/ADDRESS MARK
                    FOUND interface signal is used to report ADDRESS
                    MARK FOUND.

 When J19 is NOT installed, the drive is configured to operate in
 soft sectored mode. The SECTOR/ADDRESS MARK FOUND interface signal is
 used to transmit sector pulses to the host controller. The number of
 bytes/sector may be specified using the SET BYTES PER SECTOR command
 or by selecting a default sector configuration with option Jumpers
 J12 and J13. Three fixed sectored and one soft sectored format is
 shown in the following table.

  +--------------+---+---+---+-----------+----------+----------+
  |Sector        |J19|J12|J13|Unformatted|Formatted |Number    |
  |Configuration |   |   |   |Bytes per  |Bytes per |of Sectors|
  |              |   |   |   |Sector     |Sector    |          |
  +--------------+---+---+---+-----------+----------+----------+
  |Soft          |ON |ON |ON |Soft sectored mode               |
  +--------------+---+---+---+-----------+----------+----------+
  |Fixed         |OFF|ON |OFF|612        |512       |34        |
  +--------------+---+---+---+-----------+----------+----------+
  |Fixed         |OFF|OFF|ON |578        |512       |36        |
  +--------------+---+---+---+-----------+----------+----------+
  |Fixed         |OFF|OFF|OFF|594        |512       |35        |
  +--------------+---+---+---+-----------+----------+----------+
 For all sector configurations, the configuration response given is as
 follows:

 Minimum Bytes per ISG Field       16 bytes
 ISG Bytes after Index/sector      12 bytes
 Minimum Bytes per PLO Sync Field  14 bytes (12 bytes in 36 sector
                                   mode.


 J15 Drive Address
 -----------------
 (J15 drive address 1 through 7)
 Only one drive address jumper is installed on a 3180E drive, and the
 drive is addressed as Drive 1 at the factory. Maximum number of
 drives = 7.

 Terminator packs RP4 and RP17 provide proper termination for inter-
 face lines. When daisy chaining multiple 3180E drives, the
 terminators are installed only in the last drive on the daisy chain.

 Three Drive Select lines are to be decoded to determine the drive
 select address. Drive select jumper J15 consists of 3 jumpers which
 are configured by the user to represent a binary address (1-7).

   +----------+-----------------------+
   | SCSI ID  |        Jumpers        |
   |          | J15-3 | J15-2 | J15-1 |
   +----------+-------+-------+-------+
   |No Select | OPEN  | OPEN  | OPEN  |
   |    1     | OPEN  | OPEN  | CLOSED|
   |    2     | OPEN  | CLOSED| OPEN  |
   |    3     | OPEN  | CLOSED| CLOSED|
   |    4     | CLOSED| OPEN  | OPEN  |
   |    5     | CLOSED| OPEN  | CLOSED|
   |    6     | CLOSED| CLOSED| OPEN  |
   |    7     | CLOSED| CLOSED| CLOSED|
   +----------+-------+-------+-------+


 J9  Diagnostic Jumper
 ---------------------
     OPEN                   Normal Operation

     INSTALLED before       Cresendo Seek Test
     power up

     INSTALLED before       Random Seek Test
     power up and RE-
     MOVED after the LED
     flashes Microcode Rev
     level

 The microprocessor performs a series of "wake up" diagnostics upon
 application of power. These diagnostics must pass in order for the
 drive to become ready.

 If an error is detected, the drive microprocessor will transmit a
 vendor unique status word consisting of an error code message through
 the interface.

 If no errors are detected, the microprocessor checks the configura-
 tion of the diagnostic jumper J9. If J9 is installed before power up
 or if the Initiate Diagnostic command is initiated the drive enters
 a Diagnostic Seek Test routine. If J9 is not installed or the
 Initiate Diagnostic Command is not initiated, the drive will become
 ready and remain in an Idle state waiting for control signals.

 If an error is detected during wake up or initiated diagnostics an
 error word will be transmitted through the interface as a vendor
 unique status word. Also the error coded message will be flashed out
 through the drive LED.



**********************************************************************
                      I   N   S   T   A   L   L
**********************************************************************
MINISC.  3180E  PRODUCT MANUAL 1102 P2, 06/08/88

 Notes on Installation
 =====================

 Mounting Orientation
 --------------------
 The MiniScribe 3180E uses industry-standard mounting for 5-1/4"
 Winchester Disk Drives. The 3180E is designed to be used in
 applications where the unit may experience shock and vibration at
 greater levels than larger and heavier disk drives.

 The drive may be mounted in any attitude.

 In as much as the drive frame acts as a heat sink to dissipate heat
 from the unit, the enclosure and mounting structure should be
 designed to allow natural convection of heat around the HDA and
 outer frame. If the enclosure is small or if natural convection is
 restricted, a fan may be required.


 Daisy Chaining the MiniScribe 3180E Drives
 ------------------------------------------
 Up to seven 3180E drives may be connected to a single host
 controller/ formatter. Control signals at J1 are transmitted via
 standard, dausy-chain interconnection. Data signals at J2 are trans-
 mitted via radially connected data-transfer lines.

 Note: Interface terminators RP4 and RP17 are installed only in the
 last physical drive in the control chain. Maximum number of drives =
 7.


 Cabling
 -------
 Attach interface cables with connectors P1, P2, P3 and ground
 connector to J1, J2, J3 and ground spade connector, respectively.
 Insure that connectors P1 and P2 have keys installed. If multiple
 drives are to be interconnected, remove the terminator packs in all
 but the last drive of the daisy chain.


 J1 Connector Control Signals
 ----------------------------
 J1 is a 34 pin board edge connector on the drive printed circuit
 board. The signals on this connector control the drive and transfer
 drive status to the host controller. A key slot is provided between
 pins 4 and 6.

 Recommended mating connector: AMP ribbon connector 88373-3, or
 equivalent (key slot between pins 4 and 6).

 Recommended cable: 3M Scotchflex 3365/34 or equivalent.


 J2 Data Transfer Connector
 --------------------------
 J2 is a 20-pin board connector on the pronted circuit board. The
 signals on this connector contain read or write data. A key slot is
 provided between pins 4 and 6.

 Recommended mating connector: AMP ribbon connector 88373-6 or
 equivalent.

 Recommended cable: 3M Scotchflex 3365-20, or equivalent (keyslot be-
 tween pins 4 and 6).


 J3  DC Power Connector
 ----------------------
 J3 is a 4-pin keyed connector on the printed circuit board. DC power
 (+5V and +12V) is supplied to the drive via this connector.

 Recommended connector: AMP 350543-1
 Pins:                  AMP pin 350078-4

 Note: 1  Equivalents of the above are permissible
 Note: 2  Suggested wire size: 18 AWG

  +-----J3-----+   pin 1    +12 VDC
  | 4  3  2  1 |   pin 2    +12 Volts Return
  +------------+   pin 3    + 5 Volts Return
                   pin 4    + 5 VDC


 Frame Ground Connector
 ----------------------
 The frame ground connector is a fasten-type connection. If wire is
 used, the hole in the connector will accomodate wire size of 18 AWG
 max.

 Recommended mating connector: AMP pin 61761-2, or equivalent.


 Cable Connection
 ----------------
      HOST
 +---------------+                 +---------------+
 |               +---CONTROL-------XJ1             |
 |               |               +-X               |
 |               |    +-DATA-----+-+J2     Drive #1|
 |               |    |   +------+-+J3  Ground     |
 |               |    |   |      | +-----+---------+
 |               |    |   |    +-+-------+
 |               |    |   |    | | +---------------+
 |               |    |   |    | +-XJ1             |
 |               |    |   |    | +-X               |
 |               |    | +-+DATA+-+-+J2     Drive #2|
 | Controller    |    | | o----+-+-+J3  Ground     |
 |               |    | | |    | | +----+----------+
 |               |    | | |    o-+------+
 |               |    | | |    | | +-------------+-+ Terminator
 |               |    | | |    | +-XJ1           +-+ (Last Drive only)
 |               |    | | |    |   X               |
 |             1 +----+ |++----+---+J2     Drive #N|
 |             2 +------+|o----+---+J3  Ground     |
 |             N +-DATA--+|    |   +-----+---------+
 |               |        |    o---------+
 +---------------+        |    |
                          |    |
     DC VOLTAGES  --------+    |
     (Radial)                  |
     FRAME GROUND -------------+

 Maximum number of drives = 7

 NOTE
 Interface Terminators RP4 and RP17 are installed only in the last
 physical drive in the control chain.


 Electrical Interface
 --------------------
 The MiniScribe 3180E is pin and function compatible with the serial
 mode of the Enhanced Small Device Interface (ESDI) for 5-1/4"
 Winchester Disk Drives. In the serial mode, interface signals
 (control, data and status) are transmitted serially via handshaking
 request/acknowledge signals.

 The Enhanced Small Device Interface can be divided into three
 categories, each of which is physically separated:

 a. Control Signals
 b. Data Signals
 c. DC power


 Control Signal Drivers and Receivers
 ------------------------------------
 All control lines are digital in nature (open collector TTL) and
 either provide signals to the drive (input) or signals to the host
 (output).


 The drivers have the following electrical specifications.

 True/Active:     0.0 VDC to 0.4 VDC @ 1 = -48 mA (Max.)
 False/Deactive:  2.5 VDC to 5.25 VDC @ 1 = +250  A (Open Collector)


 Data Signal Drivers and Receivers
 ---------------------------------
 The data transfer signals are differential in nature and provide
 data either to (write) or from (read) the drive.



**********************************************************************
                      F   E   A   T   U   R   E  S
**********************************************************************
MINISC.  3180E  PRODUCT MANUAL 1102 P2, 06/08/88


 Introduction
 ------------
 The MiniScribe 3180E Series of disk drives are low cost, high
 capacity, high performance random access storage devices utilizing
 5 1/4" this film disks as storage media. Each disk surface employs
 one moveable head to access the data tracks. The 3180E Series
 features capacity of 182 megabytes (unformatted storage capacity).
 The 3180E disk drives utilize advanced 3380 Whitney-type head
 flexures and sliders which allow closer spacing of disks, allowing a
 higher number of disks in a standard 5 1/4" package.


 Seek Time (including settling time)
 -----------------------------------
       +----------------------------------+--------+
       |                                  | 3180E  |
       +----------------------------------+--------+
       |Single Track           msec. max. |   3.5  |
       +----------------------------------+--------+
       |Average                msec. typ. |  17    |
       |1/3 Stroke Seek time   msec. max. |  18    |
       |Full Stroke Seek time  msec. max. |  35    |
       |Rezero                 msec. max. | 250    |
       +----------------------------------+--------+
       |Latency                msec. avg. |   8.33 |
       +----------------------------------+--------+


 Media Defect Criteria (as shipped from MiniScribe)
 --------------------------------------------------
 Maximum Defects*             180
 2 bytes in length
 Cylinder zero defect free

 *A single defect is defined as being less than 2 bytes long. A
 multiple defect is defined as 2 bytes or longer, or as a track with
 more than 1 single defect.


 Defect List
 -----------
 The 3180E series drives are shipped with a defect list that is
 written in the ESDI Rev. F recommended format.

 The defect list resides on Sector 0 of cylinder 1249 and is repeated
 on cylinder 1241. This allows for redundancy should an error occur on
 the maximum cylinder. The Sector 0 or any surface will contain the
 defects for that surface. The format for the data field portion of
 this sector is 256 bytes with 2 bytes of CRC (x16 = 12 = x5 = 1):

  Defect locations are 5 bytes long.

  The start of the actual defect may be off by up to 7 bits due to the
  one byte resolution.

  The end of the defect list for each surface will be indicated by 5
  bytes of ones in the defect location field or the end of the sector.

  The CRC check bytes should be used if that capability exists but may
  be ignored if multiple reads are a more desirable approach. CRC
  seed is zero. (Initialized state)*.

 Byte count is the number of Bytes from Index.

 *Sync byte will be included in the CRC calculation.


 Error Message Readout
 ---------------------
 Flashing error codes are displayed through the drive LED by the
 Microprocessor to indicate hardware failures that occur while in the
 diagnostic mode (J9 installed) only. Failures during normal operation
 (connected to the host) will be reported through the ESDI interface.

 Error codes are displayed in a "morse-code" type manner. Flashes or
 bits are interpreted and converted into a hexadecimal error code.
 "Zeros" are indicated by a short (1/2 second) flashing mode. "Ones"
 are indicated by a short (1/2 second) continuous "on" mode. Error
 codes are separated by a one-second LED "off" time. All error codes
 and the revision level are 6 bits long.

 Listed Below are the binary to hexadecimal conversion values:

  00 = 000000   04 = 000100   08 = 001000   0C = 001100
  01 = 000001   05 = 000101   09 = 001001   0D = 001101
  02 = 000010   06 = 000110   0A = 001010   0E = 001110
  03 = 000011   07 = 000111   0B = 001011   0F = 001111

  10 = 010000   14 = 010100   18 = 011000   1C = 011100
  11 = 010001   15 = 010101   19 = 011001   1D = 011101
  12 = 010010   16 = 010110   1A = 011010   1E = 011110
  13 = 010011   17 = 010111   1B = 011011   1F = 011111

  30 = 110000
  31 = 110001
  32 = 110010
  39 = 111001
  3E = 111110

 Error Code Definitions
 ----------------------
 Code 00 - Microprocessor RAM error
 Code 01 - Microprocessor ROM checksum error
 Code 02 - Interface chip diagnostic failure
 Code 03 - Sector counter fault
 Code 04 - Index pulse not detected during spinup
 Code 05 - Spin speed not within 0.5% tolerance
 Code 06 - Loss of fine track during idle mode
 Code 07 - Reserved
 Code 08 - Time out on +End Decel signal (during seek)
 Code 09 - Time out on CYL Pulse (during seek)
 Code 0A - Overshoot (after a seek)
 Code 0B - Time out on fine track (after a seek)
 Code 0C - Track zero signal not detected (after a seek)
 Code 0D - Comparator mismatch (after a seek)
 Code 0E - Comparator mismatch (during a seek)
 Code 0F - Unexpected interrupt from processor
 Code 10 - Time out on non-GB pattern (during a rezero)
 Code 11 - Time out on GB1 pattern (during a rezero)
 Code 12 - Time out on GB2 pattern (during a rezero)
 Code 13 - Seek range error
 Code 14 - Voltage unsafe
 Code 15 - Track offset fault
 Code 16 - Write fault
 Code 17 - Reserved
 Code 18 - Time out on +End Decel sig (during a rezero)
 Code 19 - Time out on CYL Pulse (during a rezero)
 Code 1A - Overshoot (after a rezero)
 Code 1B - Time out on fine track (after a rezero)
 Code 1C - Track 0 signal not detected (after a rezero)
 Code 1D - Comparator mismatch (after a rezero)
 Code 30 - Time out on non-GB pattern (adj)
 Code 31 - Time out on GB1 pattern (adj)
 Code 32 - Time out on GB2 pattern (adj)
 Code 39 - Time out on CYL Pulse (adj)
 Code 3E - Cannot adjust servo


 Reliability and Maintenance
 ---------------------------
 MTBF                     35,000 POH
 MTTR                     30 minutes
 Preventive Maintenance   None
 Component Design Life    5 years


 Magnetic Field
 --------------
 The externally induced magnetic flux density may not exceed 3 Gauss
 as measured at the top of the drive.


 Spindle Drive Mechanism
 -----------------------
 A brushless DC drive motor located inside the spindle/hub assembly
 rotates the disk pack at 3600 RPM. The disk pack (including spindle,
 hub, disks, and motor) is dynamically balanced prior to installation
 to insure low vibration and servo stability.

 Dynamic braking is employed to quickly stop the drive motor when
 power is removed.


 Air Filtration System
 ---------------------
 The disks and Read/Write heads are assembled in an ultraclean air
 environment (Class 100 or better) and then sealed within the head
 disk assembly.

 Within this sealed HDA a 0.1 micron filter provides constant
 internal air filtration. In addition, a breather filter provides a
 clean, equalized pressure between internal air and ambient to the HDA
 for the life of the drive.


 Automatic carriage retract and locking
 --------------------------------------
 If power is removed from the drive during a normal power down or in
 the event of a power failure, the actuator assembly will automatic-
 ally retract and be locked in a nondata area located at the inner-
 most portion of the disk. The heads will land on and take off from
 this area only.


 Caution/Warning
 ---------------
 The Miniscribe drive is a precision product. During handling the unit
 must not be dropped, jarred or bumped. Otherwise, damage to the heads
 and disks may occur. When the drive is removed from the Miniscribe
 shipping container and not immediately secured within a chassis
 through its shock mounts, it must be stored on a padded, grounded,
 antistatic surface.

 Failure to comply with the above procedure will render null and void
 all warranties.