Your #1 Source For Out Of Production, Obsolete, And Hard To Find Hard Drives
CLICK ON THE LOGO ABOVE TO CHECK PRICE AND AVAIABILITY OF THIS DRIVE.
This information is provided as-is for free and Discount Computer Peripherals, Inc. shall not be held liable for any errors or omissions
.
Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 1922| | |
Capacity form/unform 1034/ 1203 MB Heads 15| | |
Seek time / track 14.0/ 4.0 ms Sector/track 71| | |
Controller SCSI2 DIFFERENTIAL Precompensation
Cache/Buffer 256 KB WRITE-BEHIND Landing Zone
Data transfer rate MB/S int Bytes/Sector 512
5.000 MB/S ext SYNC
Recording method RLL operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 10 50 | -40 65
Power: sleep W Humidity % 10 90 | 10 90
standby 18.0 W Altitude km -0.061 3.048| -0.305 15.240
idle W Shock g 3 | 40
seek W Rotation RPM 3600
read/write 24.0 W Acoustic dBA 40
spin-up W ECC Bit 48
MTBF h 150000
Warranty Month 60
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MICROPL. 1598/D PRODUCT DESCRIPTION 104979 REV. B
Single-Ended
+---------------------------------------------------------++-+ J2
| +-+W5 || |
| +-+ || |ID 2
| +-+W4 || |ID 1
| +-+ |+-+ID 0
| COMPONENT SIDE +-+ |XX
| | | |XX
| RN9 | |XX J1
| | | |XX
| | | |XX
| +-+ |XX
| +----+ |XX
| +----+ |XX
| W1 W2 |XX
| +---+ |X1
| Frame Ground +---W11 |
| Option +-+W28 |XX Power
| +-+ |XX J3
+---------------------------------------------------------+
Differential
+---------------------------------------------------------++-+ J2
| +-+W5 || |
| +-+ || |ID 2
| +-+W4 || |ID 1
| +-+ |+-+ID 0
| COMPONENT SIDE +-+ |XX
| | | |XX
| RN9 | |XX J1
| +-+ |XX
| +----+ |XX
| +----+ |XX
| W1 W2 |XX
| +-+ |XX
| | | |XX
| RN11 | |X1
| +-+ |
| +-+W28 W11-+ |XX Power
| +-+ +-+ |XX J3
+---------------------------------------------------------+ 1
+--------------------------------------+
| +--+J4 |
| +--+ |
| |
| +--+J5 |
| +--+ |
| J2 J1 J3 |
|.......... XXXXXXXXXXXXXXXXXX XXXXXXXX|
+-------+++------------------1--------1+
ID210 Power
**********************************************************************
J U M P E R S
**********************************************************************
MICROPL. 1598/D PRODUCT DESCRIPTION 104979 REV. B
Jumper setting
==============
x = Jumpers setting at factory
J2 SCSI ID
-----------
+----------+-----------------------+
| SCSI ID | Jumpers |
| | ID2 | ID1 | ID0 |
+----------+-------+-------+-------+
|x 0 | OPEN | OPEN | OPEN |
+----------+-------+-------+-------+
| 1 | OPEN | OPEN | CLOSED|
+----------+-------+-------+-------+
| 2 | OPEN | CLOSED| OPEN |
+----------+-------+-------+-------+
| 3 | OPEN | CLOSED| CLOSED|
+----------+-------+-------+-------+
| 4 | CLOSED| OPEN | OPEN |
+----------+-------+-------+-------+
| 5 | CLOSED| OPEN | CLOSED|
+----------+-------+-------+-------+
| 6 | CLOSED| CLOSED| OPEN |
+----------+-------+-------+-------+
| 7 | CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+
Up to eight devices (the host and seven targets) can be attached to
the SCSI bus. The 1598-15 disk drive has three ID jumpers which are
used to assign one of the eight SCSI ID bits (0 - 7) to the drive.
In multiple-device systems, each drive must have its own unique ID
bit.
Interface Terminator pack RN9 provides proper termination for the
interface, in a multiple-drive system, the terminator pack is
installed in the last drive on the system.
J2 Operator Panel Option
-------------------------
J2, Pin 19 and J2, Pins 21 through 23 are provided for interfacing
the drive to a user-supplied operator panel.
J2 Pin 19 Logic ground
20 Not used
21 Write Protect Input. Logic Ground disables writing and
lights the Write Protect LED.
22 Ready output. Logic ground indicates the drive is Ready
and lights the Ready LED.
23 +5V source for the LEDs.
J4/J5 Ground Connection
------------------------
3/16-inch spade lugs J4 and J5 are provided for grounding; system
characteristics determine proper ground connection.
W1/W2/W11 Bus Termination Power Option
---------------------------------------
+-----------------------+------------------------------------+
| Jumpers | |
| W1 | W2 | W11 | |
+-------+-------+-------+------------------------------------+
| CLOSED| OPEN | OPEN |The drive provides terminator power |
| | | |to its on-board terminators |
| | | |(Factory default configuration) |
+-------+-------+-------+------------------------------------+
| OPEN | CLOSED| OPEN |Terminator power is provided by the |
| | | |host via interface cable J1, pin 26 |
+-------+-------+-------+------------------------------------+
| OPEN | CLOSED| CLOSED|The drive provides terminator power |
| | | |to its on-board terminators and |
| | | |also to the SCSI bus via interface |
| | | |cable J1, pin 26 (TERMPWR) |
+-------+-------+-------+------------------------------------+
Under normal conditions, TERMPWR is sourced by SCSI Initiators.
There may be some unique system configurations which needs a target
to supply TERMPWR to the cable, W11 is provided for this requirement.
W4 Bus Parity Check Option
---------------------------
CLOSED The drive neither generates nor detects parity.
OPEN The drive generates parity and enables parity detection.
(Factory default configuration)
W5 Spindle Control Option
---------------------------
CLOSED The drive must wait for an interface START UNIT command
to start the spindle motor.
OPEN The drive automatically starts the spindle motor at
power-on. (Factory default configuration)
W28 Frame Ground Option
------------------------
CLOSED Frame Ground is connected to logic ground
OPEN Frame Ground is not connected to logic ground
(Factory default configuration)
**********************************************************************
I N S T A L L
**********************************************************************
MICROPL. 1598/D PRODUCT DESCRIPTION 104979 REV. B
Notes on installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
Dimensions and Mounting
-----------------------
The 1598-15 series uses industry-standard mounting techniques for
5 -inch Winchester disk drives.
Recommended orientation is vertical on either side, or horizontal
with the Device Electronics board down; other mounting orientations
may be used provided the ambient air temperature around the drive is
kept at or below 50*C (122*F).
Mounting Screws
---------------
2 per side 6-32 UNC-2B x 0.156 max deep.
4 on bottom 6-32 UNC-2B x 0.20 max deep.
Caution: The mounting screws must be selected so that they do not
penetrate the bottom mounting holes more than 0.20 inches and the
side mounting holes more than 0.156 inches. Screws that are too long
will short to PCBA components and/or prevent proper operation of the
shock mount system.
Signal Connector J1
-------------------
J1 is a 50-pin connector on the Device Electronics board. Signal
interface connection is made via this connector. The signals on J1
include the 8-bit SCSI bus and various control and handshaking lines.
Recommended Cable: 3M Scotchflex 3365/50 or equivalent
Mating Connector: 3M P/N 3425-3000 or equivalent
Multi-Function Connector J2
---------------------------
J2 is a 24-pin connector on the Device Electronics board and is used
for connecting the drive to a user-supplied Operator Panel.
Power Connector J3
------------------
J3 is a 4-pin keyed AMP MATE-N-LOCK connector on the Device
Electronics board. Both +5V and +12V is supplied to the drive via
this connector.
Suggested wire size is 18 AWG.
Recommended mating connector is AMP 1-480424-0 or equivalent.
Recommended pins are AMP 350078-4.
Ground Connectors J4/J5
-----------------------
3/16-inch spade lugs J4 and J5 are provided for grounding. Systems
characteristics determine proper ground connection.
Mating Connector: AMP 60972-2 or equivalent
Mating connector: AMP 60972-2 or equivalent.
Interface Terminator
--------------------
Interface Terminator pack RN9 provides proper termination for the
interface lines. In multiple-device systems, the terminators are
installed in the LAST device on the cable.
Multiple 1598 System Configuration
----------------------------------
Drive #1
+------HOST------+ +-----------------+
| +-----------+ +--+-SCSI-BUS-----+ J1 |
| |Terminators| | | +------+ J3 J4/J5 |
| +-----------+ | | | +--------+--------+
| | | | +------------------+
+----------------+ | | Drive #2 |
| | +-----------------+ |
+-------+------+ J1 | |
| o------+ J3 J4/J5 | |
| | +--------+--------+ |
| | +------------------+
| | Drive #3 |
| | +-----------------+ |
+-------+------+ J1 | |
| o------+ J3 J4/J5 | |
| | +--------+--------+ |
| | +------------------+
| | Drive #4 |
| | +------------+----+ |
+-------+------+ J1 | T | |
---DC-VOLTAGES-----o------+ J3 J4/J5 +----+ |
+--------+--------+ |
---GROUND--------------------------+------------------+
T = Terminator
Up to seven 1598-15 drives can be connected to a single host.
SINGLE-ENDED Interface Electrical Characteristics
-------------------------------------------------
Interface control and status signals are digital (open collector TTL)
using industry-standard transmitters and receivers.
The assigned signals are terminated with 220 ohms to +5V (nominal)
and 330 ohms to ground at each end of the cable.
All signals use open-collector or three-state drivers.
Single-ended drivers and receivers allow a maximum cable length of
six meters (primarily for connection within a cabinet).
Signal transmission requires a single 50-conductor (flat or twisted
pair) cable. A characteristic impedance of 100 ( 10%) ohms is
recommended.
a. Input Characteristics
1) Signal true = 0.0 VDC to 0.8 VDC
2) Maximum total input load = -0.4 milliamps at 0.5 VDC
3) Signal false = 2.0 VDC to 5.25 VDC
4) Minimum input hysteresis = 0.2 VDC
b. Output Characteristics
Each driven signal has the following characteristics when
measured at the interface connector.
1) Signal assertion = 0.0 VDC to 0.5 VDC
2) Minimum driver output capability = 48 milliamps (sinking) at
0.5 VDC.
3) Signal negation = 2.5 VDC to 5.25 VDC
c. Terminator Power (TERMPWR at Pin 26)
Terminator Power has the following requirements:
V(TERM) = 4.25 VDC to 5.25 VDC
800 milliamps minimum source drive capability, with 1.0 amp
recommended current limiting (e.g., a fuse).
1.0-milliamp maximum bus loading (except for the purposes of
providing power to an internal terminator).
The drive provides keyed connectors to prevent accidental grounding
or misconnection of terminator power.
DIFFERENTIAL Interface Electrical Characteristics
-------------------------------------------------
Differential interface signals consist of two signal lines which are
denoted +SIGNAL and -SIGNAL.
A signal is defined as true when the +SIGNAL is more positive than
the -SIGNAL.
A signal is defined as false when the -SIGNAL is more positive than
the +SIGNAL.
Differential drivers and receivers allow a maximum cable length of
25 meters.
Signal transmission requires a single 50-conductor cable. A
characteristic impedance of 100 ( 10%) ohms is recommended for un-
shielded flat or twisted pair ribbon cable.
A minimum conductor size of 28 AWG should be employed to minimize
noise effects and ensure proper distribution of optional terminator
power.
A stub length of no more than 0.2 meters is allowed off the main-line
interconnection within any connected equipment.
a. Input Characteristics
Each of the drive's signal receivers has the following
characteristics when measured at the interface connector.
I (input current on either input) = 2.0 milliamps, maximum
Note: These characteristics include both receivers and passive
drivers.
This requirement is met with the input voltage varying between
-7V and +12V, with power either on or off, and with hysteresis
equaling 35 millivolts, minimum.
b. Output Characteristics
Each driven signal has the following characteristics when
measured at the interface connector.
VOL (low-level output voltage) = 1.7V maximum at IOL
where IOL = 55 milliamps
VOH (high-level output voltage) = 2.7V maximum at IOH
where IOH = -55 milliamps
VOD (differential voltage) = 1.0V minimum, with common-mode
voltage ranges from -7 to +12
VOL and VOH are measured between the output terminal and the
SCSI device's logic ground reference.
c. Terminator Power (TERMPWR at Pins 25 and 26)
Terminator Power has the following requirements:
V(TERM) = 4.0 VDC to 5.25 VDC
600 milliamps minimum source drive capability, with 1.0 amp
recommended current limiting (e.g., a fuse).
1.0-milliamp maximum bus loading (except for the purposes of
providing power to an internal terminator).
The drive provides keyed connectors to prevent accidental
grounding or misconnection of terminator power.
**********************************************************************
F E A T U R E S
**********************************************************************
MICROPL. 1598/D PRODUCT DESCRIPTION 104979 REV. B
Seek Time
---------
| 1590 |
----------------------------------+--------+
Track-to-Track msec. typ. | 4 |
Average msec. typ. | 14.5 |
Maximum msec. | 33 |
One-Third Stroke msec. max. | 15.5 |
Latency msec. avg. | 8.33 |
----------------------------------+--------+