S W I F T   9 4 3 5 1 - 0 9 0    IMPRIMIS

CLick For Homepage 4drives.com
Your #1 Source For Out Of Production, Obsolete, And Hard To Find Hard Drives
CLICK ON THE LOGO ABOVE TO CHECK PRICE AND AVAIABILITY OF THIS DRIVE.

This information is provided as-is for free and Discount Computer Peripherals, Inc. shall not be held liable for any errors or omissions

.

                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/HH               Cylinders    1068|     |     |
Capacity form/unform    79/   90 MB        Heads           5|     |     |
Seek time   / track  15.0/ 4.0 ms          Sector/track   29|     |     |
Controller           SCSI1 SINGLE-ENDED    Precompensation
Cache/Buffer            64 KB READ-AHEAD   Landing Zone
Data transfer rate    1.000 MB/S int       Bytes/Sector      512
                            MB/S ext
Recording method     RLL                            operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C                 |
Power: sleep              W     Humidity     %                 |
       standby            W     Altitude    km                 |
       idle               W     Shock        g                 |
       seek               W     Rotation   RPM      3600
       read/write    11.0 W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h      70000
                                Warranty Month
Lift/Lock/Park     YES          Certificates


**********************************************************************
                        L   A   Y   O   U   T
**********************************************************************
SEAGATE  ST1090/1111/1156-N  PRODUCT DESCRIPTION

  +-------------------------------------------------------+
  |                                                       |XXXX Power
  |                                                   1+  |
  |                                                   ||  |X1
  |                                      Resistor     ||  |XX
  |                                      Termination  ++  |XX SCSI
  |                                      Packs        1+  |XX Connec-
  |                                                   ||  |XX tor
  |                                                   ||  |XX
  |                                                   ++  |XX
  |                                                   1+  |XX
  |                                                   ||  |XX
  |                                                   ||  |XX
  |                                                   ++  |+-1
  |                                                       || | SCSI ID
  |                                             TERMPWR+-+|| | J2
  +----------------------------------------------------+-+++-11




**********************************************************************
                      J   U   M   P   E   R   S
**********************************************************************
SEAGATE  ST1090/1111/1156-N  PRODUCT DESCRIPTION

 Jumper Setting
 --------------

                                                              |
                                                              |
       |                                                      |
       |                     Terminator Resistor Packs        |
 TERM- |                 +-------1  +-------1  +--------1     |
 PWR +-+                 +-------+  +-------+  +--------+     |
     +-+   11-9-7-5-3-1+                               +---+  |
       +J2-+o o o o o o+-XXXXXXXXXXXXXXXXXXXXXXXXXXXX1-+12V+--+
           |o o o o o o| XXXXXXXXXXXXXXXXXXXXXXXXXXXXX | O |Ground
          12-10-8-6-4-2+   Cable Connector             | O |Ground
            | | | +-+-+                                | 5V|
            | | |   + SCSI ID                          +---+
            | | +---- Enable Parity Checking
            | +------ Enable Motor Start Option
            +-------- Synchronized Spindle


 J2   SCSI ID jumpers
 --------------------
 +----------------+-------+-------+-------+------+-------+-------+
 |    SCSI ID     | 11-12 | 10-9  | 8-7   |6-5   | 4-3   | 2-1   |
 +----------------+-------+-------+-------+------+-------+-------+
 |         0      |       |       |       |OPEN  | OPEN  | OPEN  |
 +----------------+-------+-------+-------+------+-------+-------+
 |         1      |       |       |       |OPEN  | OPEN  | CLOSED|
 +----------------+-------+-------+-------+------+-------+-------+
 |         2      |       |       |       |OPEN  | CLOSED| OPEN  |
 +----------------+-------+-------+-------+------+-------+-------+
 |         3      |       |       |       |OPEN  | CLOSED| CLOSED|
 +----------------+-------+-------+-------+------+-------+-------+
 |         4      |       |       |       |CLOSED| OPEN  | OPEN  |
 +----------------+-------+-------+-------+------+-------+-------+
 |         5      |       |       |       |CLOSED| OPEN  | CLOSED|
 +----------------+-------+-------+-------+------+-------+-------+
 |         6      |       |       |       |CLOSED| CLOSED| OPEN  |
 +----------------+-------+-------+-------+------+-------+-------+
 |         7      |       |       |       |CLOSED| CLOSED| CLOSED|
 +----------------+-------+-------+-------+------+-------+-------+
 |Enable Parity   |       |       | CLOSED|      |       |       |
 +----------------+-------+-------+-------+------+-------+-------+
 |Start/Stop      |       | CLOSED|       |      |       |       |
 +----------------+-------+-------+-------+------+-------+-------+
 |Synchronized    |   X   |       |       |      |       |       |
 |Spindle         |       |       |       |      |       |       |
 +----------------+-------+-------+-------+------+-------+-------+
 Pin 1-2:   Least Significant Bit (LSB)
     3-4:   Next Significant Bit
     5-6:   Most Significant Bit  (MSB)


 Start/Stop option
 -----------------
 When a jumper is installed on pins 9 and 10, the drive waits for a
 Start Unit command from the host before starting the spindle motor.
 The spindle motor is also stopped using this command.


 Terminator Power Source Select (TERMPWR)
 ----------------------------------------
 ----+----+--PCB--  A-B        Drive from Power Connector (Default)
     |D  C|         A-C        Drive from SCSI Bus
     |B  A|         A-C & B-D  Drive from Power Connector and Provide
     +----+                    to SCSI Bus
                    B-D        Only Provide to SCSI Bus


 Remote LED
 ----------
      A   B
    +---+---+    Default jumper at C-D for LED mounted on drive PWA
    | * | * |    To use remote LED, remove jumper and extend B (Anode)
    +---+---+    and D (Cathode).
    | * | * |
    +---+---+
      C   D

 Swift LED kit 75912397 allows connection to a remote LED.
 Swift LED kit 95913369 has an LED for attachment to the system front
 bezel or a 5.25-inch frame kit.



**********************************************************************
                      I   N   S   T   A   L   L
**********************************************************************
SEAGATE  ST1090/1111/1156-N  PRODUCT DESCRIPTION

 Notes on installation
 =====================

 Drive mounting
 --------------

     horizontally             vertically
   +-----------------+   +--+             +--+ +------------------+
   |                 |   |  +-----+ +-----+  | |                  | x
   |                 |   |  |     | |     |  | x+----------------+x
 +-+-----------------+-+ |  |     | |     |  | ||x              x||
 +---------------------+ |  |     | |     |  | ||  x          x  ||
                         |  |     | |     |  | ||    x      x    ||
      x           x      |  |     | |     |  | ||      x  x      ||
 +------x------x-------+ |  +-----+ +-----+  | ||       xx       ||
 +-+------x--x-------+-+ +--+             +--+ ||     x    x     ||
   |       xx        |                         ||   x        x   ||
   |     x    x      |                         || x            x ||
   +---x--------x----+                         |x                x|
     x            x                           x++----------------++x
      UNACCEPTABLE!                                UNACCEPTABLE!
      Never install PC board on the Top!

 The drive may be mounted horizontally with the PC board down or on
 either side. Mounting vertically on either end is a prohibited orien-
 tation.
 For optimum performance, the drive should be formatted in the same
 position as it will be mounted in the host system.

 Do not mount the drive vertically on either end.


 Shock and vibrations
 --------------------
 All shock and vibration specifications assume that the drive is moun-
 ted in an approved orientation with the input levels at the drive
 mounting screws.

 During normal operating shock and vibration, there is no physical
 damage to the drive and performance is not degraded.

 During abnormal operating shock and vibration, there is no physical
 damage to the drive, although performance may be degraded during the
 shock or vibration episode. Drive performance will return to speci-
 fications when normal operating shock levels resume.


 Handling and Static-Discharge Precautions
 -----------------------------------------
 After unpacking, and prior to system integration, the drive may be
 exposed to potential handling and ESD hazards. It is mandatory that
 you observe standard static-discharge precautions. A grounded wrist-
 strap is preferred. Handle the drive by the frame only and always
 rest the drive on a padded surface until it is mounted in the host
 system.

 Caution: to avoid potential service problems, observe the following
 precautions:

 - Handle the drive by the edges or frame. Do not put pressure on the
   top cover or touch the circuit board.
 - Do not remove or cover factory-installed labels. They contain in-
   formation needed to service the product.
 - Do not put labels over the brather holes on the top surface of the
   drive. The breather holes must remain clear to allow air to circu-
   late.
 - If a label, other than a factory-installed label, has been placed
   over the breather holes, remove it. Do not poke holes through the
   label. This damages the filter underneath, allowing contaminants
   to enter the drive.
 - Do not use solvents to remove the adhesive residue from drive
   labels. Small amounts of solvent may get into the unit and conta-
   minate the disc.
 - Do not plug a live DC power cabel into the drive power connector.
   This damages the connector contacts.


 Terminators
 -----------
 There are three internal drive I/O termination SIP resistor modules
 that plug into sockets on the PC board. You can order the drive with
 or without these terminators, depending on the application. All
 single initiator/single target applications require that the
 initiator and drive be terminated. Daisy-chain applications require
 that only the units at each end of the daisy-chain be terminated. All
 other peripherals on the chain should not be terminated.


 Note: Remove terminator resistor packs where terminators are not
 required. Removal of terminator power source selection jumper does
 not disconnect the terminator resistors from the circuit.


 Terminator Power
 ----------------
 The drive can be configured to supply terminator power for the SCSI
 Bus. The drive also may be configured to accept terminator power via
 Pin 26 of the SCSI bus or to provide terminator power for optional
 internal termination resistors via the drive power connector. If
 terminators are installed, jumpers must also be installed.


 (Already low-level formatted at the factory)